Search result related to
if the given figure is symmetrical about vertical YYaxis the centroidal lies on

Notes

Aeronautical engineering

Lie Detector

Internship and job in eduladder

BBA 3Rd semester

Ace of Clouds: Consciousness

University of Kerala BCA 3rd semester exam

Accounting and finance 5th semester Auditing-1

6 of Clouds: The Burden

B com th semester Enterprenurship Devolepment programme

Bio medical engineering

Questions


Moment of total area about its centroidal axis is:
1 Answer

The dimensions of a symmetrical welded I-section are shown in the figure. (GATE Civil engg 2018)
1 Answer

Which answer figure will complete the pattern in the question figure? Question figure:
0 Answer

Use the figure to name: (a) Line containing point E. (b) Line passing through A. (c) Line on which O lies. (d) Two pairs of intersecting lines.-Mathematics-cbse-std 6th-Basic Geometry
1 Answer

A circular steel bar of diameter 10 mm is bent into the shape as shown in figure and lies x z plane A horizontal force P applied along positive direction The yield strength 200 MPa Neglecting effect transverse shear load Newton required to initiate yielding per maximum stress theory failure is : up two decimal places..
0 Answer

A loop carrying current I lies in the x-y plane as shown in the figure. The unit vector ˆ k is coming out of the plane of the paper. The magnetic moment of the current loop is - jee main 2012
1 Answer

The figures shown represent the analysis of gas samples collected from a sealed off area in a coal mine over a period of time. The best representation of the progressive change of gaseous environment inside the sealed-off area is
0 Answer

A circular steel bar of diameter 10 mm is bent into the shape as shown in figure, and lies in x-z plane. A horizontal force P is applied along the positive z-direction as shown. The yield strength of the steel is 200 MPa. Neglecting the effect of transverse shear, the load P (in Newton) required to initiate yielding as per maximum shear stress theory of failure is............[up to two decimal places]
0 Answer

Let X denote the number of scores which exceed 4 in 18 tosses of a symmetrical die. Consider the following statements: 1. The arithmetic mean of X is 6. 2. The standard deviation of X is 2. Which of the above statements is/are correct?
1 Answer

A steel strip of length, L = 200 mm is fixed at end A and rests at B on a vertical spring of stiffness, k = 2 N/mm. The steel strip is 5 mm wide and 10 mm thick. A vertical load, P = 50 N is applied at B, as shown in the figure. Considering E = 200 GPa, the force (in N) developed in the spring is __________. - gate civil 2017
1 Answer

For a symmetrical trapezoidal open drain in a landscape with grass and loose rock surface, the velocity of flow of water is _____ m/sec, (rounded off to two decimal places), given the following data.
0 Answer

A simple truss is shown in the figure below. The truss is loaded with horizontal and vertical force 15 kN and 25 kN, respectively. The force in the member AB will be ___________ kN.
0 Answer

What is the use of figure tag in HTML5?
1 Answer

If log5 (6 +2/x) + log1/5 (1 +x/10) <= 1, then x lies in:
0 Answer

Un easy lies that the head that wears the crown.
0 Answer

A truss is composed of members AB, BC, CD, AD and BD, as shown in the figure. A vertical load of 10 kN is applied at point D. The magnitude of force (in kN) in the member BC is____
0 Answer

The airplane shown in figure starts executing a symmetric pull-up maneuver from steady level attitude with a constant nose-up pitch acceleration of 20 deg/s2 . The vertical load factor measured at this instant at the centre of gravity (CG) is 2. Given that the acceleration due to gravity is 9.81 m/s2 , the vertical load factor measured at point P on the nose of the airplane, which is 2 m ahead of the CG, is _____ (round off to 2 decimal places).
0 Answer

A beam ABC is subjected to load P at its free end C as shown in the figure. The flexural rigidity of the beam is 􀜧􀜫. The vertical support reaction at point B is
2 Answer

A vertical well of 8000 ft is producing below bubble point pressure. Oil and water each is produced at the rate of 500 bbl/day. The indicated bottom hole pressure is 3000 psi. If the same gas to liquid ratio (GLR) is maintained, using the given figure, the new bottom hole pressure at 5000 ft is __________ psi. A vertical well of 8000 ft is producing below bubble point pressure. Oil and water each is produced at the rate of 500 bbl/day. The indicated bottom hole pressure is 3000 psi. If the same gas to liquid ratio (GLR) is maintained, the new bottom hole pressure at 5000 ft, using the given figure, is __________
0 Answer

The principal value of sin⁻¹ x lies in the interval
0 Answer
Speaks

You can do any of the following

Ask a question about this
Write a not about this