### Search result related to

An incomplete traverse table is obtained as follows Line Length m Bearing AB 1030 BC 824 13630 CD 580 22130 DA 30545 Calculate length of DA bearing of AB

**Notes**

**VTU SYLLABUS 2010SURVEYING I (COMMON TO CV/TR/EV/CTM) [10CV34]**

**CE2305 FOUNDATION ENGINEERING**

**GE2115-Computer practice Laboratory Part-5**

**SYSTEM SOFTWARE [10CS52] Unit-2**

**CE2352 DESIGN OF STEEL STRUCTURES**

**Aptitude Test :: Problems on Trains -1**

**Mechanical(First year) 10EME14**

**Aptitude Test :: Problems on Trains -3**

**Aptitude Test :: Problems on Trains -2**

**CE2204 SURVEYING I**

**Questions**

**In the following traverse ABCDEA, the length and be aring of EA is omitted. Calculate the length and bearing of line EA. (June - July 2011) Line Length (m) FB AB 204.0 87 0 30 BC 226.0 20 0 20 CD 187.0 280 0 0 DE 192.0 210 0 3 EA ?**

1 Answer

**The difference between Fore Bearing and Back Bearing of a traverse line is GATE-Agricultural Engineering-Question-2012**

1 Answer

**Following are the bearings observed in a compass traverse. Identify the stations affected by local attraction and determine corrected bearings. (Dec - 12) LINE FORE BEARING BACK BEARING AB 45 0 45 226 0 10 BC 96 0 55 277 0 05 CD 29 0 45**

1 Answer

**An abstract form a traverse sheet for a closed traverse is given below. Balance the traverse using i) Bowditchs method; ii) Transit method. (June - July 2011) LINE LENGTH (m) LATITUDE (m) DEPARTURE (m) AB 200 - 173.20 +100.00 BC 130 0.00 +130.00 C**

1 Answer

**On an old map, a line was drawn to a magnetic bearing of 320 0 30 when the declination was 3 0 30 W . Find the present bearing of the line if the declination is 4 0 15 E. ( June/July 2013 )**

1 Answer

**Define i)Magnetic bearing and true bearing ii)Whole circle bearing and reduced bearingiii) Dip and Declination. iv) Traversing v) Isogonic and Agonic lines (Dec 2012, Dec 2011, June - July 2011, June/July 2013. Dec13/Jan 14)?**

1 Answer

**In a region with magnetic declination of 2o E, the magnetic Fore bearing (FB) of a line AB was measured as N79o 50 E. There was local attraction at A. To determine the correct magnetic bearing of the line, a point O was selected at which there was no local attraction. The magnetic FB of line AO and OA were observed to be S52o 40E and N50o 20W, respectively. What is the true FB of line AB? - gate civil 2017**

1 Answer

**A uniform disc with radius r and a mass of m kg is mounted centrally on a horizontal axle of negligible mass and length of 1.5r. The disc spins counter-clockwise about the axle with angular speed ω, when viewed from the right-hand side bearing, Q. The axle precesses about a vertical axis at ωp = ω ⁄ 10 in the clockwise direction when viewed from above. Let RP and RQ (positive upwards) be the resultant reaction forces due to the mass and the gyroscopic effect, at bearings P and Q, respectively. Assuming ω 2 r = 300 m/s 2 and g = 10 m/s 2 , the ratio of the larger to the smaller bearing reaction force (considering appropriate signs) is _______**

0 Answer

**A survey line was measured to be 285.5 m with a tape having a nominal length of 30 m. On checking, the true length of the tape was found to be 0.05 m too short. If the line lay on a slope of 1 in 10, the reduced length (horizontal length) of the line for plotting of survey work would be**

0 Answer

**A steel tape of nominal length 30 m was suspended between supports to measure the length of a line. The measured length of the line on a slope of angle 3 0 50 is 29.859 m. The mean temperature during the measurement was 12 0 C and the pull applie**

1 Answer

**In a closed loop traverse of 1 km total length, the closing errors in departure and latitude are 0.3 m and 0.4 m, respectively. The relative precision of this traverse will be: - gate civil 2017**

1 Answer

**If a line is inclined to Vertical Plane and parallel to Horizontal Plane, then which of the following statements is always correct ?**

0 Answer

**I f the departure and latitude of a line during Theodolite survey are 70.03 m and -100 m, respectively, the whole circle bearing of this line in degree is (GATE-Agricultural-Engineering-2018)**

0 Answer

**A square footing of 4 m side is placed at 1 m depth in a sand deposit. The dry unit weight () of sand is 15 kN/m3 . This footing has an ultimate bearing capacity of 600 kPa. Consider the depth factors: dq = d = 1.0 and the bearing capacity factor: N = 18.75. This footing is placed at a depth of 2 m in the same soil deposit.**

0 Answer

**Cards bearing numbers 1, 3, 5, _ _ _, 35 are kept in a bag. A card is drawn at random from the bag. Find the probability of getting a card bearing CBSE Mathematics**

1 Answer

**In a closed loop traverse of 1 km total length, the closing errors in departure and latitude are 0.3 m and 0.4 m, respectively. The relative precision of this traverse will be: - gate civil 2017**

1 Answer

**In a closed loop traverse of 1 km total length, the closing errors in departure and latitude are 0.3 m and 0.4 m, respectively. The relative precision of this traverse will be: - gate civil 2017**

1 Answer

**A self-aligning ball bearing has a basic dynamic load rating (C10, for 106 revolutions) of 35 kN. If the equivalent radial load on the bearing is 45 kN, the expected life (in 106 revolutions) is (Gate 2018 Mechanical Engineering)**

0 Answer

**Two identical ball bearings P and Q are operating at loads 30kN and 45kN respectively. -gate-mechanical-2011**

1 Answer

**A Mendelian experiment consisted of breeding pea plants bearing violet flowers with pea plants bearing white flowers. What will be the result in F1 progeny ?**

1 Answer

**Speaks**

## You can do any of the following

Ask a question about thisWrite a not about this