See Our team
Wondering how we keep quality?
Got unsolved questions? Ask Questions
Engineering GATE CBSE NCERT Psychology English Computer Constitution Astrology Yoga Economics Physics Biology Electronics Microprocessor Career Interview Anatomy Botany
You might be intrested on below oppertunities Show me All
n a process, the number of cycles to failure decreases exponentially with an increase in load. At a load of 80 units, it takes 100 cycles for failure. When the load is halved, it takes 10000 cycles for failure. The load for which the failure will hap1 AnswerCollapse of the World Trade Center (WTC), New York, in 2001, was due to (GATE-Architecture-Planning-2018)0 AnswerHow can I use Load Cell as a vehicle sensor?1 AnswerA circular steel bar of diameter 10 mm is bent into the shape as shown in figure and lies x z plane A horizontal force P applied along positive direction The yield strength 200 MPa Neglecting effect transverse shear load Newton required to initiate yielding per maximum stress theory failure is : up two decimal places..0 AnswerMaintenance releases and technical assistance centers are examples of which of the following costs of quality? (3M)23 AnswerFailure in an interview1 AnswerA circular steel bar of diameter 10 mm is bent into the shape as shown in figure, and lies in x-z plane. A horizontal force P is applied along the positive z-direction as shown. The yield strength of the steel is 200 MPa. Neglecting the effect of transverse shear, the load P (in Newton) required to initiate yielding as per maximum shear stress theory of failure is............[up to two decimal places]0 AnswerStructural Compressive Load A steel pipe 10 feet long is able to withstand 15 tonnes of tensile load Can you trust this pipe to withstand 15 tonne compressive load?1 AnswerA four stroke cycle petrol engine requires for strokes of the piston to complete0 AnswerWhy is it necessary to define a Test Strategy?1 AnswerWe can achieve complete statement coverage but still miss bugs because: 1 AnswerA watch uses two electronic circuits (ECs). Each EC has a failure probability of 0.1 in one year of operation. Both ECs are required for functioning of the watch. The probability of the watch functioning for one year without failure is1 AnswerWhich one of following is NOT correct? (Gate mechanical engineering 2014)1 AnswerIn a steel plate with bolted connections, the rupture of the net section is a mode of failure under -Civil Engineering-gate-20121 AnswerConsider the expression (a-1) * ((( b + c ) / 3 )) + d)). Let X be the minimum number of registers required by an optimal code generation (without any register spill) algorithm for a load/store architecture, in which : -gate computer science 20171 AnswerConsider the expression (a-1) * ((( b + c ) / 3 )) + d)). Let X be the minimum number of registers required by an optimal code generation (without any register spill) algorithm for a load/store architecture, in which : -gate computer science 20171 AnswerT he instruction pipeline of a RISC processor has the following stages: Instruction Fetch (IF), Instruction Decode (ID), Operand Fetch (OF), Perform Operation (PO) and Writeback (WB). The IF, ID, OF and WB stages take 1 clock cycle each for every instruction. Consider a sequence of 100 instructions. In the PO stage, 40 instructions take 3 clock cycles each, 35 instructions take 2 clock cycles each, and the remaining 25 instructions take 1 clock cycle each. Assume that there are no data hazards and no control hazards. The number of clock cycles required for completion of execution of the sequence of instructions is ______.1 AnswerA single-phase 100 kVA, 1000 V / 100 V, 50 Hz transformer has a voltage drop of 5% across its series impedance at full load. Of this, 3% is due to resistance. The percentage regulation of the transformer at full load with 0.8 lagging power factor is0 AnswerA watch uses two electronic circuits (ECs). Each EC has a failure probability of 0.1 in one year of operation. Both ECs are required for functioning of the watch. The probability of the watch functioning for one year without failure 8 AnswerThe load which doesn't change its magnitude and position with time is called0 Answer