See Our team

Wondering how we keep quality?

Got unsolved questions?

Ask Questions

Engineering
GATE
CBSE
NCERT
Psychology
English
Computer
Constitution
Astrology
Yoga
Economics
Physics
Biology
Electronics
Microprocessor
Career
Interview
Anatomy
Botany

New updates

Searching for :EngineeringDate:2019-05-22 01:55:14Done by:Anonymous user(Visitor)Searching for :EngineeringDate:2019-05-22 01:54:13Done by:Anonymous user(Visitor)

Searching for :What is it calladDate:2019-05-22 01:50:20Done by:Anonymous user(Visitor)

### Similar Questions

**A shaft with a circular cross-section is subjected to pure twisting moment. The ratio of the maximum shear stress to the largest principal stress isGate-2016**

1 Answer

**A motor is driving a solid circular steel shaft transmits 40kW of power at 500 rpm. If the diameter of the shaft is 40 mm, The maximum shear stress in the shaft is ____ MPa.**

1 Answer

**A composite circular shaft is comprised of a steel core surrounded by an aluminum annulus, perfectly bonded to each other as shown in the fi gure. If it subjected to a pure torque, which one of the following statements is TRUE? GATE-**

1 Answer

**In stress strain curve of mild steel Ultimate Tensile Stress is**

1 Answer

**Which one of following is NOT correct? (Gate mechanical engineering 2014)**

1 Answer

**What is the maximum shear stress induced in the shaft of diameter 40 mm.**

1 Answer

**A force of 8.0 kN is applied perpendicularly to the axis of a crankpin having circular cross-sectional area. The allowable shear stress of the crankpin material is 40.0 N mm-2. If the crankpin fails under double shear, the design diameter of the cran**

1 Answer

**A single crystal of aluminium is subjected to 10 MPa tensile stress along the [321] crystallographic direction. The resolved shear stress on the (111̅ ) [101] slip system is ______ (in MPa to two decimal places)**

0 Answer

**Consider a beam with circular cross-section of diameter d. The ratio of the second moment of area about the neutral axis to the section modulus of the area is.**

1 Answer

**In the engineering stress-strain curve for mild steel, the Ultimate Tensile Strength (UTS) refers to**

1 Answer

**A cantilever beam having a rectangular cross-section of width 60 mm and depth 100 mm, is made of aluminum alloy. The material mechanical properties are: Young’s modulus, E = 73 GPa and ultimate stress, 𝜎𝑢=480 MPa. Assuming a factor of safety of 4, the maximum bending moment (in kN-m) that can be applied on the beam is _____ (accurate to one decimal place). (GATE-Aerospace-Engineering-2018)**

0 Answer

**A thin cylindrical pressure vessel with closed-ends is subjected to internal pressure. The ratio of circumferential (hoop) stress to the longitudinal stress is Gate-2016**

1 Answer

**A thin cylinder (thickness, and diameter, ) with closed ends is subjected to an internal pressure, . The ratio of hoop stress to longitudinal stress developed in the wall of the cylinder is**

1 Answer

**Consider the singly reinforced beam shown in the figure below:At cross-section XX, which of the following statements is TRUE at the limit state? - gate civil 2017**

1 Answer

**L ength, width and thickness of a plate are 400 mm, 400 mm and 30 mm, respectively. For the material of the plate, Young’s modulus of elasticity is 70 GPa, yield stress is 80 MPa and Poisson’s ratio is 0.33. When the plate is subjected to a longitudinal tensile stress of 70 MPa, the increase in the volume (in mm3) of the plate is ______**

0 Answer

**A steel rod was subjected to a fluctuating stress cycle that varied between a maximum of 400 MPa in tension to a minimum of 300 MPa in compression. What is the stress amplitude, in MPa?______. (-Gate metallurgical engineering 2014)**

1 Answer

**A simply supported beam AB of span, L = 24 m is subjected to two wheel loads acting at a distance, d = 5 m apart as shown in the figure below. Each wheel transmits a load, P = 3 kN and may occupy any position along the beam. If the beam is an I-section having section modulus, S = 16.2 cm 3 , the maximum bending stress (in GPa) due to the wheel loads is _______________________. - gate civil 2017**

1 Answer

**The maximum bending stress at the fixed end of the cantilever is (GATE-CIVIL-Engg-2018)**

0 Answer

**In a fillet weld, the direct shear stress and bending tensile stress are 50 MPa and 150 MPa, respectively. As per IS 800: 2007, the equivalent stress (in MPa, up to two decimal places) will be ______ (GATE-CIVIL-Engg-2018)**

0 Answer

**A hollow circular shaft of inner radius 10 mm, outer radius 20 mm and length 1 m is to be used as a torsional spring. If the shear modulus of the material of the shaft is 150 GPa, the torsional stiffness of the shaft (in kN-m/rad) is ________ (correct to two decimal places).**

1 Answer

### Notes

**VTU SYLLABUS 2010 STRENGTH OF MATERIALS (COMMON TO CV/TR/EV/CTM) [10CV33] Engineering.**

**CE2201 MECHANICS OF SOLIDS**

**10me34 Mechanics of materials**

**CE2252 STRENGTH OF MATERIALS**

**CE2251 SOIL MECHANICS**

**CE 2404 PRESTRESSED CONCRETE STRUCTURE**

**7 of Fire: Stress**

**CE2302 STRUCTURAL ANALYSIS I**

**CE2257 STRENGTH OF MATERIALS LABORATORY**

**CE2306 DESIGN OF RC ELEMENTS**

Loading More post

## A shaft with a circular cross-section is subjected to pure twisting moment. The ratio of the maximum shear stress to the largest principal stress isGate-2016

(A) 2.0

(B) 1.0

(C) 0.5

(D) 0

Asked by:13priya

Taged users:

Likes:

Be first to like this question

Dislikes:

Be first to dislike this question

Talk about this Delete Like Dislike

AnswersLikes:

Be first to like this answer

Dislikes:

Be first to dislike this answer

Talk about this Delete Like Dislike

## Can you help us to add better answer here? Please see this

You may also like our videosBelow are some of the videos from our collection. We saw that students not only needed content but also videos. So, we decided to build a video platform for you also an algorithm which shows best videos suites to you related to the content you are browsing check out some videos which suit best for you.

Lets together make the web is a better placeWe made eduladder by keeping the ideology of building a supermarket of all the educational material available under one roof. We are doing it with the help of individual contributors like you, interns and employees. So the resources you are looking for can be easily available and accessible also with the freedom of remix reuse and reshare our content under the terms of creative commons license with attribution required close.

You can also contribute to our vision of "Helping student to pass any exams"with these.Answer a question:You can answer the questions not yet answered in eduladder.How to answer a questionCareer:Work or do your internship with us.Work with usCreate a video:You can teach anything and everything each video should be less than five minutes should cover the idea less than five min.How to upload a video on eduladderDonate:Ad revenue alone is not able to take care of our server cost consider donating at least a dollar Click here to donate.