
See Our team
Wondering how we keep quality?
Got unsolved questions? Ask Questions
GATE
GMAT
CBSE
NCERT
Career
Interview
Railway
UPSC
NID
NIFT-UG
NIFT-PG
PHP
AJAX
JavaScript
Node Js
Shell Script
Research
New updates
Career 2.0
You might be intrested on below oppertunities Show me All
Similar Questions
The major and minor principal stresses at a point are 25 MPa and -5 MPa respectively. The maximum shear stress, in MPa at that point is _______.0 AnswerThe state of stress at a point in a component is represented by a Mohr’s circle of radius 100 MPa centered at 200 MPa on the normal stress axis. On a plane passing through the same point, the normal stress is 260 MPa. The magnitude of the shear stress on the same plane at the same point is ______ MPa.0 AnswerIf 1 and 3 are the algebraically largest and smallest principal stresses respectively, the value of the maximum shear stress is (Gate 2018 Mechanical Engineering)0 AnswerAt a critical point in a component, the state of stress is given as 100MPa xx , 220MPa yy , 80MPa xy yx and all other stress components are zero. The yield strength of the material is 468 MPa. The factor of safety on the basis of maximum shear stress theory is ______ (round off to one decimal place).0 Answer(Gate 2018 Mechanical engineering) The state of stress at a point, for a body in plane stress, is shown in the figure below. If the minimum principal stress is 10 kPa, then the normal stress y (in kPa) is 0 AnswerConsider the stress-strain curve for an ideal elastic-plastic strain hardening metal as shown in the figure. The metal was loaded in uniaxial tension starting from O. Upon loading, the stress-strain curve passes through initial yield point at P, and then strain hardens to point Q, where the loading was stopped. From point Q, the specimen was unloaded to point R, where the stress is zero. If the same specimen is reloaded in tension from point R, the value of stress at which the material yields again is _________ MPa.0 AnswerWhich one of following is NOT correct? (Gate mechanical engineering 2014)1 AnswerA shaft with a circular cross-section is subjected to pure twisting moment. The ratio of the maximum shear stress to the largest principal stress isGate-20161 AnswerT he maximum and the minimum principal stresses are denoted by σ1 and σ3, respectively. The differential stress can have an absolute value greater than σ1 when1 AnswerA plane-strain compression (forging) of a block is shown in the figure. The strain in the z-direction is zero. The yield strength (Sy) in uniaxial tension/compression of the material of the block is 300 MPa and it follows the Tresca (maximum shear stress) criterion. Assume that the entire block has started yielding. At a point where 40 MPa (compressive) and 0, x xy the stress component y is0 AnswerAt a point in a stressed body, sum of the normal stresses acting on perpendicular faces of an arbitrarily oriented plane stress element is always0 AnswerThe insitu stress field around a circular tunnel is shown in the figure. Points A and B are located at the boundary of the tunnel. If the tangential stress at Point A is 3 times of that at Point B, the value of insitu stress ratio, k is _________.0 AnswerA thin walled cylindrical pressure vessel with an inside diameter of 300 mm and wall thickness of 3 mm is subjected to an internal gauge pressure of 1.5 MPa. The maximum shear stress (in MPa) at a point located on the inner surface of the pressure vessel is ______0 AnswerThe sum of the focal distance of a point on an ellipse is constant and equal to the0 AnswerFrom an elevated point A, when a stone is thrown vertically, it attains an upward velocity of v at a height of h from the point A. While falling, its downward velocity becomes 2v at a distance h below the point A. The maximum height attained by the stone from point A is0 AnswerA simply supported beam ABC is subjected to load as shown in the figure. The 20 kN load is applied at point B with the help of a welded bracket as shown. The beam has a rectangular cross-section of 15 mm width and 100 mm depth as shown. The maximum transverse shear stress developed in the beam (in MPa) is ........[up to one decimal place]0 AnswerIn a structural member under fatigue loading, the minimum and maximum stresses developed at the critical point are 50 MPa and 150 MPa, respectively. The endurance, yield, and the ultimate strengths of the material are 200 MPa, 300 MPa and 400 MPa, re1 AnswerThe critical temperature above which ferromagnetic materials lose their magnetic property is called2 AnswerWhich of the following is not a physical property? (NIFT)1 AnswerIn a semi-monocoque construction of an aircraft wing, the skin and spar webs are the primary carriers of GATE-Aerospace Engineering-Question-20121 Answer
Notes
CE2201 MECHANICS OF SOLIDSVTU SYLLABUS 2010 STRENGTH OF MATERIALS (COMMON TO CV/TR/EV/CTM) [10CV33] Engineering.10me34 Mechanics of materialsCE2252 STRENGTH OF MATERIALSCE 2035 ROCK ENGINEERINGCE2251 SOIL MECHANICSCE 2404 PRESTRESSED CONCRETE STRUCTURECE2257 STRENGTH OF MATERIALS LABORATORYCE2308 SOIL MECHANICS LABORATORY CE 2041 BRIDGE STRUCTURES
Career 2.0
The major and minor principal stresses at a point are 25 MPa and -5 MPa respectively. The maximum shear stress, in MPa at that point is _______.
We made eduladder by keeping the ideology of building a supermarket of all the educational material available under one roof. We are doing it with the help of individual contributors like you, interns and employees. So the resources you are looking for can be easily available and accessible also with the freedom of remix reuse and reshare our content under the terms of creative commons license with attribution required close.
You can also contribute to our vision of "Helping student to pass any exams" with these. Answer a question: You can answer the questions not yet answered in eduladder.How to answer a question Career: Work or do your internship with us.Work with us Create a video: You can teach anything and everything each video should be less than five minutes should cover the idea less than five min.How to upload a video on eduladder