In eduladder you can Ask,Answer,Listen,Earn and Download Questions and Question papers.

Watch related videos of your favorite subject.

Connect with students from different parts of the world.

Apply or Post Jobs, Courses ,Internships and Volunteering opportunity. For FREE

See Our team

Wondering how we keep quality?

Got unsolved questions? Ask Questions

GATE
GMAT
CBSE
NCERT
Career
Interview
Railway
UPSC
NID
NIFT-UG
NIFT-PG
PHP
AJAX
JavaScript
Node Js
Shell Script
Research

New updates

Searching for :InterviewDate:2021-06-22 02:11:44Done by:Anonymous user(Visitor)Searching for :CBSEDate:2021-06-22 02:11:36Done by:Anonymous user(Visitor)

Searching for :NIDDate:2021-06-22 02:11:32Done by:Anonymous user(Visitor)

View All

Career 2.0

You might be intrested on below oppertunities Show me All

Posted By:Eduladder

Posted By:Eduladder

### Similar Questions

**The live load and dead load in a three storeyed residential building, transferred through a single column, is 12 tons and 18 tons respectively. If the soil bearing capacity is 10 ton/sqm and the factor of safety is 1.5, the area of column footing is _____________ sqm (up to one decimal place). (GATE-Architecture-Planning-2018)**

2 Answer

**The load on a RCC column is 150 kN. The soil bearing capacity is 80 kN/m2 . Assuming a factor of safety of 1.2, the side of the square column footing is _______ meter (rounded off to one decimal place).**

0 Answer

**the axial load carrying capacity of the column (in kN, up to one decimal place), is ______ (GATE-CIVIL-Engg-2018)**

1 Answer

**A square cross-section wooden column of length 3140 mm is pinned at both ends. For the wood, Young’s modulus of elasticity is 12 GPa and allowable compressive stress is 12 MPa. The column needs to support an axial compressive load of 200 kN. Using a factor of safety of 2.0 in the computation of Euler’s buckling load, the minimum cross-sectional area (in mm2) of the column is ______**

0 Answer

**A square footing of 4 m side is placed at 1 m depth in a sand deposit. The dry unit weight () of sand is 15 kN/m3 . This footing has an ultimate bearing capacity of 600 kPa. Consider the depth factors: dq = d = 1.0 and the bearing capacity factor: N = 18.75. This footing is placed at a depth of 2 m in the same soil deposit.**

0 Answer

**A square footing (2 m x 2 m) is subjected to an inclined point load, P as shown in the figure below. The water table is located well below the base of the footing. Considering one-way eccentricity, the net safe load carrying capacity of the footing for a factor of safety of 3.0 is _______________ kN. The following factors may be used - gate civil 2017**

1 Answer

**The length of the pile required for the above design load with a factor of safety of 2.0 is (GATE-CIVIL-Engg-2018)**

1 Answer

**Using limit state method and neglecting the self weight of base plate and steel column, the length of a side of the base plate to be provided is (GATE-CIVIL-Engg-2018)**

1 Answer

**The width of a square footing and the diameter of a circular footing are equal. If both the footings are placed on the surface of sandy soil, the ratio of the ultimate bearing capacity of circular footing to that of square footing will be (GATE-CIVIL-Engg-2018)**

1 Answer

**A column of height h with a rectangular cross-section of size a×2a has a buckling load of P. If the cross-section is changed to 0.5a × 3a and its height changed to 1.5h, the buckling load of the redesigned column will be (GATE-CIVIL-Engg-2018)**

1 Answer

**Four columns of a building are to be located within a plot size of 10 m x 10 m. The expected load on each column is 4000 kN. Allowable beari ng capacity of the soil deposit is 100 kN/m 2 . The type of foundation best suited is, GATE- Civil Engine**

1 Answer

**A Single Phase Neutral (SPN) electrical circuit has a power consumption of 330W. Considering a voltage of 110V and power factor of 0.8, the electrical current drawn is ___________ Amp (up to one decimal place). (GATE-Architecture-Planning-2018)**

1 Answer

**A single-phase transformer of rating 25 kVA, supplies a 12 kW load at power factor of 0.6 lagging. The additional load at unity power factor in kW (round off to two decimal places) that may be added before this transformer exceeds its rated kVA is __________.**

0 Answer

**A bar is subjected to a combination of a steady load of 60 kN and a load fluctuating between10 kN and 90 kN. The corrected endurance limit of the bar is 150 MPa, the yield strength of the material is 480 MPa and the ultimate strength of the material is 600 MPa. The bar cross-section is square with side a. If the factor of safety is 2, the value of a (in mm), according to the modified Goodman’s criterion, is ________ (correct to two decimal places).**

1 Answer

**A water tank is to be constructed on the soil deposit shown in the figure below. A circular footing of diameter 3 m and depth of embedment 1 m has been designed to support the tank. The total vertical load to be taken by the footing is 1500 kN. Assume the unit weight of water as 10 kN/m3 and the load dispersion pattern as 2V:1H. The expected settlement of the tank due to primary consolidation of the clay layer is _______________ mm. - gate civil 2017**

1 Answer

**Q39 - gate civil 2017**

1 Answer

**The ratio of the theoretical critical buckling load for a column with fixed ends to that of another column with the same dimensions and material, but with pinned ends, is equal to-Civil Engineering-gate-2012**

1 Answer

**(Gate 2018 Mechanical engineering)A steel column of rectangular section (15 mm × 10 mm) and length 1.5 m is simply supported at both ends. Assuming modulus of elasticity, E = 200 GPa for steel, the critical axial load (in kN) is ____**

0 Answer

**In a mixed use development on a 2.0 hectare site with 2.0 FAR, the ratio of residential to commercial floor area is 3:2. The minimum parking (in ECS) needed per 100 sqm of residential and commercial floor area is 1.0 and 1.25 respectively. Considering full FAR utilization, the total parking requirement is ____________ ECS. (GATE-Architecture-Planning-2018)**

1 Answer

**A self-aligning ball bearing has a basic dynamic load rating (C10, for 106 revolutions) of 35 kN. If the equivalent radial load on the bearing is 45 kN, the expected life (in 106 revolutions) is (Gate 2018 Mechanical Engineering)**

0 Answer

### Notes

**CE2306 DESIGN OF RC ELEMENTS**

**CE2305 FOUNDATION ENGINEERING**

**CE2025 ARCHITECTURE**

**VTU SYLLABUS 2010 BUILDING MATERIALS AND CONSTRUCTION TECHNOLOGY (COMMON TO CV/TR/CTM) [10CV32] Engineering.**

**CE2208 COMPUTER AIDED BUILDING DRAWING**

**Ten cms Part-2**

**(GATE-Architecture-Planning-2018)**

**CE 2402 ESTIMATION AND QUANTITY SURVEYING**

**CE2251 SOIL MECHANICS**

**STORAGE AREA NETWORK [12SCS322] Unit-1 VTU**

## The live load and dead load in a three storeyed residential building, transferred through a single column, is 12 tons and 18 tons respectively. If the soil bearing capacity is 10 ton/sqm and the factor of safety is 1.5, the area of column footing is _____________ sqm (up to one decimal place). (GATE-Architecture-Planning-2018)

The live load and dead load in a three storeyed residential building, transferred through a single column, is 12 tons and 18 tons respectively. If the soil bearing capacity is 10 ton/sqm and the factor of safety is 1.5, the area of column footing is _____________ sqm (up to one decimal place). (GATE-Architecture-Planning-2018)Asked On2019-04-10 14:33:56 by:naikaumprakash

Taged users:

Likes:

Be first to like this question

Dislikes:

Be first to dislike this question

Talk about this Like Dislike

Download question setAnswersTotal Load = Live load + Dead Load = 12 tons + 18 tons =30 tons

Factor of safety = 1.5

So total considerable load for designing of column footing = 30 tons x 1.5 = 45 tons

Load bearing capacity of soil = 10 tons/ sqm

So area required for footing = (45 tons)/ (10 tons/ sqm) = 4.5 sqm

Likes:

|RSHAH12

Dislikes:

Be first to dislike this answer

Talk about this Like Dislike

## You might like this video:Network and IP Address

Watch more here

## Watch more videos from this user Here

Learn how to upload a video over here

otal Load = Live load + Dead Load = 12 tons + 18 tons =30 tons

Factor of safety = 1.5

So total considerable load for designing of column footing = 30 tons x 1.5 = 45 tons

Load bearing capacity of soil = 10 tons/ sqm

So area required for footing = (45 tons)/ (10 tons/ sqm) = 4.5 sqm

Likes:

Be first to like this answer

Dislikes:

Be first to dislike this answer

Talk about this Like Dislike

## You might like this video:Network and IP Address

Watch more here

## Watch more videos from this user Here

Learn how to upload a video over here

Lets together make the web is a better placeWe made eduladder by keeping the ideology of building a supermarket of all the educational material available under one roof. We are doing it with the help of individual contributors like you, interns and employees. So the resources you are looking for can be easily available and accessible also with the freedom of remix reuse and reshare our content under the terms of creative commons license with attribution required close.

You can also contribute to our vision of "Helping student to pass any exams"with these.Answer a question:You can answer the questions not yet answered in eduladder.How to answer a questionCareer:Work or do your internship with us.Work with usCreate a video:You can teach anything and everything each video should be less than five minutes should cover the idea less than five min.How to upload a video on eduladder