See Our team
Wondering how we keep quality?
Got unsolved questions? Ask Questions
You might be intrested on below oppertunities Show me All
A coarse sand aquifer has porosity 20% and hydraulic conductivity 3.5x10^-3 m/s. If the hydraulic gradient is 0.00423 (m/m), then the average linear velocity of the groundwater in mm/s, (rounded off to three decimal places) is __________.0 AnswerSpecific discharge of 1 cm per day is observed in a porous medium where hydraulic head difference is 0.5 m and flow length is 20 m. Calculate the hydraulic conductivity (in m/day). GATE-Geology and Geophysics-Question-20121 AnswerTransmissivity of an aquifer is the product of ________.0 AnswerIn a soil specimen, the total stress, effective stress, hydraulic gradient and critical hydraulic gradient are , ', i and ic, respectively. For initiation of quicksand condition, which one of the following statements is TRUE?0 AnswerHydraulic brakes used in automobiles are based on (NIFT UG)1 AnswerF urrows of 120 m length with 0.5% slope are made at 90 cm spacing. The maximum nonerosive stream flow rate is applied in a furrow that takes 1.0 hour to reach the lower end. Then this flow rate is reduced to half of its size and, subsequently, continued for another 1.0 hour. The average depth of applied water is ________ cm. (GATE-Agricultural-Engineering-2018)0 AnswerAgricultural Engineering: Question0 AnswerThe depths from the soil surface to subsurface tile drains, impermeable soil layer and the highest water table are measured as 2.8 m, 5.0 m and 0.8 m, respectively. The effective hydraulic head for drainage in meter is (GATE-Agricultural-Engineering-2018)0 AnswerA soil has a void ratio of 0.75 and a specific gravity of 2.66. The value of critical hydraulic gradient at which quick sand condition will occur is. GATE- Agricultural Engineering- 20131 AnswerAn electric field E⃗ = E0 ẑis applied to a Hydrogen atom in n = 2 excited state. Ignoring spin, the n = 2 state is fourfold degenerate, which in the |l, m⟩ basis are given by |0,0〉, |1,1⟩, |1,0⟩ and |1, −1⟩. If H′ is the interaction Hamiltonian corresponding to the applied electric field, which of the following matrix elements is nonzero?0 AnswerA voltage 1000 sin ωt Volts is applied across YZ. Assuming ideal diodes, the voltage measured across WX in Volts, is GATE-Instrumentational-Engineering-20131 AnswerA 2 m^3 biogas plant is to be operated using cow-dung as feedstock. The cow-dung is mixed with water in proportion of 1:1 (by weight) to form a slurry of density 1090 kg m^-3. The yield of biogas is 0.036 m^3 kg^-1 of cow-dung. If the hydraulic retention time is 40 days, volume of the digester of the biogas plant will be ________ m^3. (GATE-Agricultural-Engineering-2018)0 AnswerA force P is applied at a distance x from the end of the beam as shown in the figure. What would be the value of x so that the displacement at ‘A’ is equal to zero? (-Gate mechanical engineering 2014)1 AnswerA bar of circular cross section is clamped at ends P and Q as shown in the figure. A torsional moment T = 150 Nm is applied at a distance of 100 mm from end P. The torsional reactions (TP, TQ) in Nm at the ends P and Q respectively are (Gate 2018 Mechanical engineering)0 AnswerA four-wheel vehicle of mass 1000 kg moves uniformly in a straight line with the wheels revolving at 10 rad/s. The wheels are identical, each with a radius of 0.2 m. Then a constant braking torque is applied to all the wheels and the vehicle experien1 AnswerA cantilever beam having a rectangular cross-section of width 60 mm and depth 100 mm, is made of aluminum alloy. The material mechanical properties are: Young’s modulus, E = 73 GPa and ultimate stress, 𝜎𝑢=480 MPa. Assuming a factor of safety of 4, the maximum bending moment (in kN-m) that can be applied on the beam is _____ (accurate to one decimal place). (GATE-Aerospace-Engineering-2018)1 AnswerWrite a note on hydraulics and hydraulic machines1 AnswerShear strength of rock joint is NOT dependent on0 AnswerWhat is Surveying, Building Materials, Construction Technology, Geotechnical Engineering, Structural Engineering, Hydraulics, WaterResources and Irrigation Engineering, Transportation Engineering, Environmental Engineering.?-elements of civil enginee1 AnswerA pumping device that combines the advantages of both centrifugal and reciprocating pumps is known as GATE-Agricultural Engineering-Question-20121 Answer
CE2253 APPLIED HYDRAULIC ENGINEERINGCE2301 IRRIGATION ENGINEERING10me43power plant engineering6ME404 Hydraulic Machinery NotesCE2258 HYDRAULIC ENGINEERING LABAG2211 APPLIED GEOLOGY GE2151 BASIC ELECTRICAL AND ELECTRONICS ENGINEERINGCE 2046 WIND ENGINEERINGVTU SYLLABUS 2010 (Civil) APPLIED ENGINEERING GEOLOGY 10CV36 Engineering