See Our team
Wondering how we keep quality?
Got unsolved questions? Ask Questions
Engineering GATE CBSE NCERT Psychology English Computer Constitution Astrology Yoga Economics Physics Biology Electronics Microprocessor Career Interview Anatomy Botany
Stress path equation for tri-axial test upon application of deviatoric stress is, q root10 3 root 0.5 p . The respective values of cohesion, c (in kPa) and angle of internal friction, fiy are: - gate civil 2017 1 AnswerA thin-walled cylindrical can with rigid end caps has a mean radius 100R mm and a wall thickness of 5 t mm. The can is pressurized and an additional tensile stress of 50 MPa is imposed along the axial direction as shown in the figure. Assume that the state of stress in the wall is uniform along its length. If the magnitudes of axial and circumferential components of stress in the can are equal, the pressure (in MPa) inside the can is ___________ (correct to two decimal places).0 AnswerIn stress strain curve of mild steel Ultimate Tensile Stress is1 AnswerConsider the singly reinforced beam shown in the figure below:At cross-section XX, which of the following statements is TRUE at the limit state? - gate civil 2017 1 AnswerIn the engineering stress-strain curve for mild steel, the Ultimate Tensile Strength (UTS) refers to1 AnswerIn a fillet weld, the direct shear stress and bending tensile stress are 50 MPa and 150 MPa, respectively. As per IS 800: 2007, the equivalent stress (in MPa, up to two decimal places) will be ______ (GATE-CIVIL-Engg-2018)1 AnswerA thin cylindrical pressure vessel with closed-ends is subjected to internal pressure. The ratio of circumferential (hoop) stress to the longitudinal stress is Gate-20161 AnswerA thin cylinder (thickness, and diameter, ) with closed ends is subjected to an internal pressure, . The ratio of hoop stress to longitudinal stress developed in the wall of the cylinder is1 AnswerA steel member ‘M’ has reversal of stress due to live loads, whereas another member ‘N’ has reversal of stress due to wind load. As per IS 800: 2007, the maximum slenderness ratio permitted is: - gate civil 20171 AnswerA conventional drained triaxial compression test was conducted on a normally consolidated clay sample under an effective confining pressure of 200 kPa. The deviator stress at failure was found to be 400 kPa. An identical specimen of the same clay sample is isotropically consolidated to a confining pressure of 200 kPa and subjected to standard undrained triaxial compression test. If the deviator stress at failure is 150 kPa, the pore pressure developed (in kPa, up to one decimal place) is ______ (GATE-CIVIL-Engg-2018)0 AnswerAn open belt drive system transmits 5 kW power using a flat belt of width and thickness as 80 mm and 5 mm, respectively. The driving shaft speed is 1500 rpm and the driven shaft speed is 500 rpm. The coefficient of friction between the belt and pulley is 0.20, and the wrap angle of the belt is 168°. If diameter of the smaller pulley is 200 mm, maximum stress induced in the belt will be _________ MPa. (GATE-Agricultural-Engineering-2018)0 AnswerA single crystal of aluminium is subjected to 10 MPa tensile stress along the  crystallographic direction. The resolved shear stress on the (111̅ )  slip system is ______ (in MPa to two decimal places)0 AnswerThe respective units for dislocation density and stress intensity factor are: (-Gate metallurgical engineering 2014)1 AnswerT he void ratio of a soil is 0.55 at an effective normal stress of 140 kPa. The compression index of the soil is 0.25. In order to reduce the void ratio to 0.4, an increase in the magnitude of effective normal stress (in kPa, up to one decimal place) should be ______ (GATE-CIVIL-Engg-2018)0 AnswerThe maximum bending stress at the fixed end of the cantilever is (GATE-CIVIL-Engg-2018)0 AnswerA spherical pressure vessel (made of mild steel) of internal diameter 500 mm and thickness 10 mm is subjected to an internal gauge pressure of 4000 kPa. If the yield stress of mild steel is 200 MPa, the factor of safety (up to one decimal place) is ______0 AnswerTwo triangular wedges are glued together as shown in the following figure. The stress acting normal to the interface, - gate civil 2017 1 AnswerA steel rod was subjected to a fluctuating stress cycle that varied between a maximum of 400 MPa in tension to a minimum of 300 MPa in compression. What is the stress amplitude, in MPa?______. (-Gate metallurgical engineering 2014)1 AnswerL ength, width and thickness of a plate are 400 mm, 400 mm and 30 mm, respectively. For the material of the plate, Young’s modulus of elasticity is 70 GPa, yield stress is 80 MPa and Poisson’s ratio is 0.33. When the plate is subjected to a longitudinal tensile stress of 70 MPa, the increase in the volume (in mm3) of the plate is ______0 AnswerAn infinite plate with a through-thickness crack of length 2 mm is subjected to a tensile stress (as shown in the figure). Assuming the plate to be linear elastic, the fracture stress is ____________ MPa (round off to the nearest whole number) (Given: Fracture toughness, 𝐾𝐼𝐶=25 𝑀𝑃𝑎 √𝑚)0 Answer
CE2257 STRENGTH OF MATERIALS LABORATORYCE2251 SOIL MECHANICSVTU SYLLABUS 2010 STRENGTH OF MATERIALS (COMMON TO CV/TR/EV/CTM) [10CV33] Engineering.CE2201 MECHANICS OF SOLIDSCE2252 STRENGTH OF MATERIALS7 of Fire: StressGE2152 BASIC CIVIL & MECHANICAL ENGINEERINGData structure with C 10CS35 unit-810me34 Mechanics of materialsVTU SYLLABUS 2010 (Civil) FLUID MECHANICS [10CV35] Engineering
Loading More post